Can I Install a Bath Tub Myself? Factors to Consider As Well As Steps
Can I Install a Bath Tub Myself? Factors to Consider As Well As Steps
Blog Article
Every person is bound to have their personal way of thinking when it comes to A Step-by-Step Guide to Installing a Bathtub.
Installing a bathtub isn't specifically rocket science, yet it does need solid plumbing, woodworking, and occasionally, tiling skills. Changing an old bathtub with a brand-new one is also a reasonably challenging task. If the old tub is conveniently available, the task can move speedily; if you have to open up a wall to eliminate the old tub as well as position the brand-new tub, the job is much harder. In either case, the job is within a residence handyman's abilities, although you will certainly need an assistant to move out the old bathtub as well as set in the brand-new one. Make sure you have actually qualified on your own for the job and also are comfortable trying it. As opposed to employing a contractor to take over a halfway-completed task, it is much better to consider utilizing one prior to you begin. Opportunities are you may require a professional plumber to make tube connections.
This write-up will certainly assist you mount a new bath tub in your restroom if you have currently purchased a brand-new tub as well as do not require to change the plan of your previous water supply pipes.
Your devices and material list should make up the following:
Preparing for the Setup
Firstly, the supporting structure supplied with the bathroom needs to be fitted (if called for) according to the producer's directions. Next off, fit the taps or mixer to the tub. When suitable the faucet block, it is important to ensure that if the tap includes a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bathroom, it is likewise practical to fit a supporting plate under the taps unit to prevent strain on the bath tub.
Fit the adaptable faucet adapters to the bottom of both taps making use of 2 nuts and also olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet via the hole in the bathroom. Utilize the nut supplied by the producer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bath. Ensure you utilize all of the supplied washers.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect the bottom of the overflow tube in a similar manner.The bath should now be ready to be fitted in its last position.
Removing Old Taps
If you need to change old faucets with brand-new ones as a part of your installment, after that the first thing you need to do is separate the water. After doing so, activate the faucets to drain pipes any type of water staying in the system. The process of eliminating the existing taps can be quite problematic as a result of the limited accessibility that is usually the instance.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipelines to the taps. Have a cloth ready for the remaining water that will certainly originate from the pipes. Once the supply pipes have actually been gotten rid of, utilize the very same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the single taps from turning throughout this procedure. When the taps have actually been gotten rid of, the holes in the bath/basin will have to be cleansed of any kind of old sealing compound.
Prior to proceeding to fit the brand-new taps, contrast the pipe links on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the new faucets to fit.
Mounting the Bath tub
Utilizing both wooden boards under its feet, place the bath tub in the needed position. The wood boards are valuable in evenly spreading out the weight of the tub over the area of the boards rather than concentrating all the weight onto 4 small factors.
The next goal is to make sure that the bathtub is leveled all round. This can be attained by inspecting the spirit level and also adjusting the feet on the bath tub up until the spirit level reviews level.
To mount taps, fit all-time low of the furthest flexible faucet connector to the proper supply pipe by making a compression sign up with; then do the exact same for the various other tap.
Turn on the water supply as well as examine all joints and brand-new pipework for leakages as well as tighten them if needed. Fill the tub as well as also inspect the overflow electrical outlet and the typical electrical outlet for leaks.
Lastly, repair the bathroom paneling as defined in the manufacturer's user's manual. Tiling and also sealing around the bathtub ought to wait up until the bath tub has been utilized at the very least when as this will settle it right into its last position.
Fitting New Touches
If the tails of the brand-new faucets are plastic, after that you will need a plastic port to stop damages to the thread. One end of the port fits on the plastic tail of the faucet and also the various other end provides a connection to the existing supply pipelines.
If you require to fit a monobloc, then you will need minimizing couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next, position the tap in the installing opening in the bath/basin making sure that the washing machines remain in area in between the tap and the sink. Protect the tap in position with the supplier given backnut. Once the tap is securely in place, the supply pipes can be linked to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with regular faucet adapters. The previous kind needs to be attached to the faucet finishes initially, tightening up just by hand. The supply pipelines can later be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Tub
In the location where the bathroom satisfies the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is very important as the installation can relocate sufficient to split a stiff seal, causing the water to penetrate the wall between the bathroom and also the tiling, bring about difficulties with wetness and also feasible leakages to the ceiling below.
You can select from a variety of coloured sealants to assimilate your components and fittings. They are marketed in tubes and also cartridges, and also are capable of securing voids as much as a size of 3mm (1/8 inch). If you have a larger space to fill up, you can fill it with twists of soaked newspaper or soft rope. Remember to always fill the bath tub with water prior to securing, to permit the activity experienced when the bathtub is in use. The sealant can crack fairly early if you do not take into account this activity prior to securing.
Additionally, ceramic coving or quadrant floor tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are additionally conveniently readily available on the marketplace. It is a good idea to fit the ceramic tiles using water-resistant or water resistant adhesive and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I found that review about How to Install a Bathtub Yourself when surfing the search engines. Are you aware of someone else who is interested in the niche? Do not hesitate to share it. I recognize the value of reading our article about A Step-by-Step Guide to Installing a Bathtub.
Schedule Here
Report this page